View AD5323BRUZ-REEL_4194257.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

2.5 v to 5.5 v, 230 a, dual rail-to-rail voltage output 8-/10-/12-bit dacs ad5303/ad5313/ad5323 rev. b information furnished by analog devices is believed to be accurate and reliable. however, no responsibility is assumed by analog devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. specifications subject to change without notice. no license is granted by implication or otherwise under any patent or patent rights of analog devices. trademarks and registered trademarks are the property of their respective owners. one technology way, p.o. box 9106, norwood, ma 02062-9106, u.s.a. tel: 781.329.4700 www.analog.com fax: 781.461.3113 ?1999C2007 analog devices, inc. all rights reserved. features ad5303: 2 buffered 8-bit dacs in 1 package a version: 1 lsb inl, b version: 0.5 lsb inl ad5313: 2 buffered 10-bit dacs in 1 package a version: 4 lsb inl, b version: 2 lsb inl ad5323: 2 buffered 12-bit dacs in 1 package a version: 16 lsb inl, b version: 8 lsb inl 16-lead tssop package micropower operation: 300 a @ 5 v (including reference current) power-down to 200 na @ 5 v, 50 na @ 3 v 2.5 v to 5.5 v power supply double-buffered input logic guaranteed monotonic by design over all codes buffered/unbuffered reference input options output range: 0 v to v ref or 0 v to 2 v ref power-on-reset to 0 v sdo daisy-chaining option simultaneous update of dac outputs via ldac pin asynchronous clr facility low power serial interface with schmitt-triggered inputs on-chip rail-to-rail output buffer amplifiers applications portable battery-powered instruments digital gain and offset adjustment programmable voltage and current sources programmable attenuators general description the ad5303/ad5313/ad5323 are dual 8-/10-/12-bit buffered voltage output dacs in a 16-lead tssop package that operate from a single 2.5 v to 5.5 v supply, consuming 230 a at 3 v. their on-chip output amplifiers allow the outputs to swing rail-to- rail with a slew rate of 0.7 v/s. the ad5303/ad5313/ad5323 utilize a versatile 3-wire serial interface that operates at clock rates up to 30 mhz and is compatible with standard spi, qspi?, microwire?, and dsp interface standards. the references for the two dacs are derived from two reference pins (one per dac). these reference inputs may be configured as buffered or unbuffered inputs. the parts incorporate a power- on reset circuit, which ensures that the dac outputs power up to 0 v and remain there until a valid write to the device takes place. there is also an asynchronous active low clr pin that clears both dacs to 0 v. the outputs of both dacs may be updated simultaneously using the asynchronous ldac input. the parts contain a power-down feature that reduces the current consumption of the devices to 200 na at 5 v (50 na at 3 v) and provides software-selectable output loads while in power-down mode. the parts may also be used in daisy- chaining applications using the sdo pin. the low power consumption of these parts in normal operation makes them ideally suited to portable battery-operated equip- ment. the power consumption is 1.5 mw at 5 v and 0.7 mw at 3 v, reducing to 1 w in power-down mode. functional block diagram dac register power-down logic buffer string dac string dac ad5303/ad5313/ad5323 input register input register dac register interface logic sclk power-on reset v dd v ref a v out a v out b gnd v ref b ldac din 00472-001 sync clr pd buf b buffer sdo dcen buf a resistor network resistor network gain-select logic figure 1.
ad5303/ad5313/ad5323 rev. b | page 2 of 28 table of contents features .............................................................................................. 1 applications....................................................................................... 1 general description ......................................................................... 1 functional block diagram .............................................................. 1 revision history ............................................................................... 2 specifications..................................................................................... 3 ac characteristics........................................................................ 6 timing characteristics ................................................................ 6 absolute maximum ratings............................................................ 8 esd caution.................................................................................. 8 pin configuration and function descriptions............................. 9 terminology .................................................................................... 10 typical performance characteristics ........................................... 11 functional description .................................................................. 15 digital-to-analog ....................................................................... 15 resistor string ............................................................................. 15 dac reference inputs ............................................................... 15 output amplifier........................................................................ 15 power-on reset .............................................................................. 16 clear function ( clr ) ................................................................ 16 serial interface ................................................................................ 17 input shift register .................................................................... 17 low power serial interface ....................................................... 17 double-buffered interface ........................................................ 17 power-down modes ...................................................................... 19 microprocesser interfacing ........................................................... 20 ad5303/ad5313/ad5323 to adsp-2101 interface............. 20 ad5303/ad5313/ad5323 to 68hc11/68l11 interface ...... 20 ad5303/ad5313/ad5323 to 80c51/80l51 interface.......... 20 ad5303/ad5313/ad5323 to microwire interface ........ 20 applications information .............................................................. 21 typical application circuit....................................................... 21 bipolar operation using the ad5303/ ad5313/ad5323 . .... 21 opto-isolated interface for process control applications ... 22 decoding multiple ad5303/ad5313/ad5323s.................... 22 ad5303/ad5313/ad5323 as a digitally programmable window detector ....................................................................... 22 coarse and fine adjustment using the ad5303/ad5313/ad5323 ....................................................... 23 daisy-chain mode ..................................................................... 23 power supply bypassing and grounding................................ 24 outline dimensions ....................................................................... 25 ordering guide .......................................................................... 25 revision history 6/07rev. a to rev. b updated format..................................................................universal changes to table 4............................................................................ 8 changes to the ordering guide.................................................... 25 8/03rev. 0 to rev. a added a version.................................................................universal changes to features.......................................................................... 1 changes to specifications ................................................................ 2 changes to absolute maximum ratings ....................................... 5 changes to ordering guide ............................................................ 5 updated outline dimensions ....................................................... 18 4/99revision 0: initial version
ad5303/ad5313/ad5323 rev. b | page 3 of 28 specifications v dd = 2.5 v to 5.5 v; v ref = 2 v; r l = 2 k to gnd; c l = 200 pf to gnd; all specifications t min to t max , unless otherwise noted. table 1. a version 1 b version 1 parameter 2 min typ max min typ max unit conditions/comments dc performance 3 , 4 ad5303 resolution 8 8 bits relative accuracy 0.15 1 0.15 0.5 lsb differential nonlinearity 0.02 0.25 0.02 0 .25 lsb guaranteed monotonic by design over all codes ad5313 resolution 10 10 bits relative accuracy 0.5 4 0.5 2 lsb differential nonlinearity 0.05 0.5 0.05 0.5 lsb guaranteed monotonic by design over all codes ad5323 resolution 12 12 bits relative accuracy 2 16 2 8 lsb differential nonlinearity 0.2 1 0.2 1 lsb guaranteed monotonic by design over all codes offset error 0.4 3 0.4 3 % of fsr see figure 2 and figure 3 gain error 0.15 1 0.15 1 % of fsr see figure 2 and figure 3 lower dead band 10 60 10 60 mv see figure 2 and figure 3 offset error drift 5 ?12 ?12 ppm of fsr/c gain error drift 5 ?5 ?5 ppm of fsr/c power supply rejection ratio 5 ?60 ?60 db v dd = 10% dc crosstalk 5 30 30 v dac reference inputs 5 1 v dd 1 v dd v buffered reference mode v ref input range 0 v dd 0 v dd v unbuffered reference mode >10 >10 m buffered reference mode 180 180 k unbu ffered reference mode 0 v to v ref output range, input impedance = r dac 90 90 k unbu ffered reference mode v ref input impedance 0 v to 2 v ref output range, input impedance = r dac reference feedthrough ?90 ?90 db frequency = 10 khz channel-to-channel isolation ?80 ?80 db frequency = 10 khz output characteristics 5 minimum output voltage 6 0.001 0.001 v min maximum output voltage 6 v dd ? 0.001 v dd ? 0.001 v max this is a measure of the minimum and maximum drive capability of the output amplifier dc output impedance 0.5 0.5 short-circuit current 50 50 ma v dd = 5 v 20 20 ma v dd = 3 v power-up time 2.5 2.5 s coming out of power-down mode; v dd = 5 v 5 5 s coming out of power-down mode; v dd = 3 v
ad5303/ad5313/ad5323 rev. b | page 4 of 28 a version 1 b version 1 parameter 2 min typ max min typ max unit conditions/comments logic inputs 5 input current 1 1 a 0.8 0.8 v v dd = 5 v 10% 0.6 0.6 v v dd = 3 v 10% input low voltage, v il 0.5 0.5 v v dd = 2.5 v 2.4 2.4 v v dd = 5 v 10% 2.1 2.1 v v dd = 3 v 10% input high voltage, v ih 2.0 2.0 v v dd = 2.5 v pin capacitance 2 3.5 2 3.5 pf logic output (sdo) 5 v dd = 5 v 10% output low voltage 0.4 0.4 v i sink = 2 ma output high voltage 4.0 4.0 v i source = 2 ma v dd = 3 v 10% output low voltage 0.4 0.4 v i sink = 2 ma output high voltage 2.4 2.4 v i source = 2 ma floating-state leakage current 1 1 a dcen = gnd floating-state output capacitance 3 3 pf dcen = gnd power requirements v dd 2.5 5.5 2.5 5.5 v i dd specification is valid for all dac codes i dd (normal mode) both dacs active and excluding load currents v dd = 4.5 v to 5.5 v 300 450 300 450 a v dd = 2.5 v to 3.6 v 230 350 230 350 a both dacs in unbuffered mode; v ih = v dd and v il = gnd; in buffered mode, extra current is typically x a per dac, where x = 5 a + v ref /r dac i dd (full power-down) v dd = 4.5 v to 5.5 v 0.2 1 0.2 1 a v dd = 2.5 v to 3.6 v 0.05 1 0.05 1 a 1 temperature range for version a, version b: ?40c to +105c. 2 see the terminology section. 3 dc specifications tested with the outputs unloaded. 4 linearity is tested using a reduced code range: ad5303 (code 8 to code 248); ad5313 (code 28 to code 995); ad5323 (code 115 to code 3981). 5 guaranteed by design and characterization, not production tested. 6 in order for the amplifier output to reach its minimum voltage, offset error must be negative. in order for the amplifier outp ut to reach its maximum voltage, v ref = v dd and offset plus gain error must be positive.
ad5303/ad5313/ad5323 rev. b | page 5 of 28 dac code gain error plus offset erro r output voltage positive offset error negative offset error amplifier footroom (1mv) 0 0472-005 actual ideal d e a d b a n d figure 2. transfer function with negative offset 00472-006 actual ideal dac code positive offset error output v oltage gain error plus offset error figure 3. transfer function with positive offset
ad5303/ad5313/ad5323 rev. b | page 6 of 28 ac characteristics 1 v dd = 2.5 v to 5.5 v; r l = 2 k to gnd; c l = 200 pf to gnd; all specifications t min to t max , unless otherwise noted. table 2. a, b version 3 parameter 2 min typ max unit conditions/comments output voltage settling time v ref = v dd = 5 v ad5303 6 8 s ? scale to ? scale change (0x40 to 0xc0) ad5313 7 9 s ? scale to ? scale change (0x100 to 0x300) ad5323 8 10 s ? scale to ? scale change (0x400 to 0xc00) slew rate 0.7 v/s major-code transition glitch energy 12 nv-s 1 lsb change around major carry (011 . . . 11 to 100 . . . 00) digital feedthrough 0.10 nv-s analog crosstalk 0.01 nv-s dac-to-dac crosstalk 0.01 nv-s multiplying bandwidth 200 khz v ref = 2 v 0.1 v p-p, unbuffered mode total harmonic distortion ?70 db v ref = 2.5 v 0.1 v p-p, frequency = 10 khz 1 guaranteed by design and characterization, not production tested. 2 see the terminology section. 3 temperature range for version a and version b: ? 40c to +105c. timing characteristics v dd = 2.5 v to 5.5 v; all specifications t min to t max , unless otherwise noted. table 3. limit at t min, t max parameter 1 , 2 , 3 (a, b version) unit conditions/comments t 1 33 ns min sclk cycle time t 2 13 ns min sclk high time t 3 13 ns min sclk low time t 4 0 ns min sync to sclk rising edge setup time t 5 5 ns min data setup time t 6 4.5 ns min data hold time t 7 0 ns min sclk falling edge to sync rising edge t 8 100 ns min minimum sync high time t 9 20 ns min ldac pulse width t 10 20 ns min sclk falling edge to ldac rising edge t 11 20 ns min clr pulse width t 12 4 , 5 5 ns min sclk falling edge to sdo invalid t 13 4 , 5 20 ns max sclk falling edge to sdo valid t 14 5 0 ns min sclk falling edge to sync rising edge t 15 5 10 ns min sync rising edge to sclk rising edge 1 guaranteed by design and characterization, not production tested. 2 all input signals are specified with tr = tf = 5 ns (10% to 90% of v dd ) and timed from a voltage level of (v il + v ih )/2. 3 see figure 4 and figure 5. 4 these are measured with the load circuit of figure 4. 5 daisy-chain mode on ly (see figure 47).
ad5303/ad5313/ad5323 rev. b | page 7 of 28 2ma i ol 2ma i oh 1.6v to output pin c l 50pf 00472-002 figure 4. load circuit for digital output (sdo) timing specifications sclk s ync din* db15 db0 ldac ldac clr * see the input shift register section. t 1 t 2 t 3 t 4 t 5 t 6 t 7 t 8 t 9 t 10 t 11 00472-003 figure 5. serial interface timing diagram
ad5303/ad5313/ad5323 rev. b | page 8 of 28 absolute maximum ratings t a = 25c, unless otherwise noted. 1 table 4. parameter rating v dd to gnd ?0.3 v to +7 v digital input voltage to gnd ?0.3 v to v dd + 0.3 v digital output voltage to gnd ?0.3 v to v dd + 0.3 v reference input voltage to gnd ?0.3 v to v dd + 0.3 v v out a, v out b to gnd ?0.3 v to v dd + 0.3 v operating temperature range industrial (a, b version) ?40c to +105c storage temperature range ?65c to +150c junction temperature (t j max) 150c 16-lead tssop package power dissipation (t j max ? t a )/ ja ja thermal impedance 160c/w lead temperature jedec industry standard soldering j-std-020 1 transient currents of up to 100 ma do not cause scr latch-up. stresses above those listed under absolute maximum ratings may cause permanent damage to the device. this is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. exposure to absolute maximum rating conditions for extended periods may affect device reliability. esd caution
ad5303/ad5313/ad5323 rev. b | page 9 of 28 pin configuration and fu nction descriptions 1 2 3 4 5 6 7 8 ldac v dd v ref b buf a v out a v ref a clr buf b 16 15 14 13 12 11 10 9 gnd din sclk pd dcen v out b sync sdo ad5303/ ad5313/ ad5323 top view (not to scale) 00472-004 figure 6. pin configuration table 5. pin function descriptions pin no. mnemonic description 1 clr active low control input. loads all zeros to both input and dac registers. 2 ldac active low control input. transfers the contents of the input registers to their respective dac registers. pulsing this pin low allows either or both dac registers to be updated if the input registers have new data. this allows the simultaneous update of both dac outputs. 3 v dd power supply input. these parts can be operated from 2.5 v to 5.5 v, and the supply should be decoupled to gnd. 4 v ref b reference input pin for dac b. it may be configured as a buffered or an unbuffered input, depending on the state of the buf b pin. it has an input range from 0 v to v dd in unbuffered mode and from 1 v to v dd in buffered mode. 5 v ref a reference input pin for dac a. it may be configured as a buffered or an unbuffered input depending on the state of the buf a pin. it has an input range from 0 to v dd in unbuffered mode and from 1 v to v dd in buffered mode. 6 v out a buffered analog output voltage from dac a. the output amplifier has rail-to-rail operation. 7 buf a control pin. controls whether the reference input for dac a is unbuffered or buffered. if this pin is tied low, the reference input is unbuffered. if it is tied high, the reference input is buffered. 8 buf b control pin. controls whether the reference input for dac b is unbuffered or buffered. if this pin is tied low, the reference input is unbuffered. if it is tied high, the reference input is buffered. 9 dcen this pin is used to enable the daisy-chaining option. this should be tied high if the part is being used in a daisy chain. the pin should be tied low if it is being used in standalone mode. 10 pd active low control input. acts as a hardware power-down option. this pin overrides any software power-down option. both dacs go into power-down mode when this pin is tied low. the dac outputs go into a high impedance state and the current consumption of th e part drops to 200 na @ 5 v (50 na @ 3 v). 11 v out b buffered analog output voltage from dac b. the output amplifier has rail-to-rail operation. 12 sync active low control input. this is the frame sy nchronization signal for the input data. when sync goes low, it powers on the sclk and din buffers and enables the input shift register. data is transferred in on the falling edges of the following 16 clocks. if sync is taken high before the 16th falling edge, the rising edge of sync acts as an interrupt and the write sequ ence is ignored by the device. 13 sclk serial clock input. data is clocked into the input shift register on the falling edge of the serial clock input. data can be transferred at rates up to 30 mhz. the sclk in put buffer is powered down after each write cycle. 14 din serial data input. this device has a 16-bit shift register. da ta is clocked into the register on the falling edge of the serial clock input. the din input buffer is powered down after each write cycle. 15 gnd ground reference point for all circuitry on the part. 16 sdo serial data output. can be used for daisy-chaining a number of these devices together or for reading back the data in the shift register for diagnostic purposes. the serial data output is valid on the falling edge of the clock.
ad5303/ad5313/ad5323 rev. b | page 10 of 28 terminology relative accuracy or integral nonlinearity (inl) for the dac, relative accuracy or integral nonlinearity is a measure of the maximum deviation, in lsb, from a straight line passing through the actual endpoints of the dac transfer function. a typical inl error vs. code plot can be seen in figure 7 , figure 8 , and figure 9 . differential nonlinearity (dnl) differential nonlinearity is the difference between the measured change and the ideal 1 lsb change between any two adjacent codes. a specified dnl of 1 lsb maximum ensures monotonic- ity. this dac is guaranteed monotonic by design. a typical dnl error vs. code plot can be seen in figure 10 , figure 11 , and figure 12 . offset error this is a measure of the offset error of the dac and the output amplifier. it is expressed as a percentage of the full-scale range. gain error this is a measure of the span error of the dac. it is the devia- tion in slope of the actual dac transfer characteristic from the ideal expressed as a percentage of the full-scale range. offset error drift this is a measure of the change in offset error with changes in temperature. it is expressed in (ppm of full-scale range)/c. gain error drift this is a measure of the change in gain error with changes in temperature. it is expressed in (ppm of full-scale range)/c. major-code transition glitch energy major-code transition glitch energy is the energy of the impulse injected into the analog output when the code in the dac register changes state. it is normally specified as the area of the glitch in nv-s and is measured when the digital code is changed by 1 lsb at the major carry transition (011 . . . 11 to 100 . . . 00 or 100 . . . 00 to 011 . . . 11). digital feedthrough digital feedthrough is a measure of the impulse injected into the analog output of the dac from the digital input pins of the device, but is measured when the dac is not being written to ( sync held high). it is specified in nv-s and is measured with a full-scale change on the digital input pins, that is, from all 0s to all 1s and vice versa. analog crosstalk this is the glitch impulse transferred to the output of one dac due to a change in the output of the other dac. it is measured by loading one of the input registers with a full-scale code change (all 0s to all 1s and vice versa) while keeping ldac high. then pulse ldac low and monitor the output of the dac whose digital code was not changed. the area of the glitch is expressed in nv-s. dac-to-dac crosstalk this is the glitch impulse transferred to the output of one dac due to a digital code change and subsequent output change of the other dac. this includes both digital and analog crosstalk. it is measured by loading one of the dacs with a full-scale code change (all 0s to all 1s and vice versa) while keeping ldac low and monitoring the output of the other dac. the area of the glitch is expressed in nv-s. dc crosstalk this is the dc change in the output level of one dac in response to a change in the output of the other dac. it is measured with a full-scale output change on one dac while monitoring the other dac. it is expressed in microvolts. power supply rejection ratio (psrr) this indicates how the output of the dac is affected by changes in the supply voltage. psrr is the ratio of the change in v out to a change in v dd for full-scale output of the dac. it is measured in decibels. v ref is held at 2 v and v dd is varied 10%. reference feedthrough this is the ratio of the amplitude of the signal at the dac output to the reference input when the dac output is not being updated (that is, ldac is high). it is expressed in decibels. total harmonic distortion (thd) this is the difference between an ideal sine wave and its attenuated version using the dac. the sine wave is used as the reference for the dac and the thd is a measure of the harmonics present on the dac output. it is measured in decibels. multiplying bandwidth the amplifiers within the dac have a finite bandwidth. the multiplying bandwidth is a measure of this. a sine wave on the reference (with full-scale code loaded to the dac) appears on the output. the multiplying bandwidth is the frequency at which the output amplitude falls to 3 db below the input. channel-to-channel isolation this is a ratio of the amplitude of the signal at the output of one dac to a sine wave on the reference input of the other dac. it is measured in decibels.
ad5303/ad5313/ad5323 rev. b | page 11 of 28 typical performance characteristics 1.0 0.5 0 ?0.5 ?1.0 0 50 100 150 200 250 00472-007 t a = 25 c v dd = 5v inl error (lsb) code figure 7. ad5303 typical inl plot 3 1 0 ?2 ?3 0 200 400 600 800 1000 t a = 25 c v dd = 5v ?1 2 12 4 0 ?8 ?12 0 1000 2000 3000 4000 00472-009 ?4 8 00472-008 inl error (lsb) code figure 8. ad5313 typical inl plot t a = 25 c v dd = 5v inl error (lsb) code figure 9. ad5323 typical inl plot 0.3 0.1 0 ?0.2 ?0.3 0 50 100 150 250 00472-010 ?0.1 0.2 t a = 25 dnl error (lsb) code 200 c v dd = 5v figure 10. ad5303 typical dnl plot 0.6 0.2 0 ?0.4 ?0.6 0 200 400 600 800 1000 00472-011 ?0.2 0.4 t a = 25 c v dd = 5v dnl error (lsb) code figure 11. ad5313 typical dnl plot 1.0 0.5 0 ?0.5 ?1.0 0 1000 2000 3000 4000 00472-012 t a = 25 c v dd = 5v dnl error (lsb) code figure 12. ad5323 typical dnl plot
ad5303/ad5313/ad5323 rev. b | page 12 of 28 0.75 0.25 0 ?0.75 ?1.00 2345 00472-013 ?0.50 0.50 max inl max dnl min dnl min inl t a = 25 error (lsb) v ref (v) c v dd = 5v ?0.25 1.00 figure 13. ad5303 inl and dnl error vs. v ref 0.75 0.25 0 ?0.75 ?1.00 04 08 01 2 0 00472-014 ?0.50 0.50 ?0.25 1.00 max dnl v dd = 5v v ref = 3v ?40 min dnl min inl max inl 0.5 0 ?1.0 0 40 80 120 00472-015 ?0.5 1.0 ?40 temperature (c) error (lsb) figure 14. ad5303 inl error and dnl error vs. temperature v dd = 5v v ref =2v gain error offset error temperature (c) error (%) figure 15. offset error and gain error vs. temperature 0 100 150 200 250 300 350 400 00472-016 v dd = 5v v dd = 3v i dd (a) frequency figure 16. i dd histogram with v dd = 3 v and v dd = 5 v 4 1 ?0 0123456 00472-017 v out (v) sink/source current (ma) 2 3 5 3v source 5v source 5v sink 3v sink figure 17. source and si nk current capability 600 400 300 100 0 zero scale full scale 00472-018 i dd (a) 200 500 t a = 25 c v dd = 5v figure 18. supply current vs. code
ad5303/ad5313/ad5323 rev. b | page 13 of 28 600 400 300 100 0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 00472-019 i dd (a) 200 500 v dd (v) both dacs in gain-of-two mode reference inputs buffered +105 c +25 c ? 40 c figure 19. supply current vs. supply voltage 1.0 0.9 0 0.4 0.3 0.2 0.1 0.8 0.6 0.7 0.5 both dacs in three-state condition i dd (a) v dd (v) 2.7 3.2 3.7 4.2 4.7 5.2 ?40c +25c +105c 00472-020 figure 20. power-down current vs. supply voltage 500 400 200 100 0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 00472-021 i dd (a) 300 700 v logic (v) t a = 25 c v dd = 5v v dd = 3v 600 figure 21. supply current vs. logic input voltage c h2 ch1 1v, ch2 5v, time base = 5s/div 00472-022 c h1 v dd = 5v t a = 25 c clk v out figure 22. half-scale settling (? to ? scale code change) ch2 ch1 1v, ch2 1v, time base = 20s/div 00472-023 ch1 v out a t a = 25 c v dd figure 23. power-on reset to 0 v ch3 ch1 1v, ch3 5v, time base = 1s/div 00472-024 ch1 t a = 25 c v out clk figure 24. exiting po wer-down to midscale
ad5303/ad5313/ad5323 rev. b | page 14 of 28 2.48 2.47 00472-025 v out (v) 2.49 2.50 1s/div 00472-027 2mv/di v 500ns/div figure 27. dac-to -dac crosstalk figure 25. ad5323 major-code transition ?60 ?50 ?40 ?30 ?20 ?10 0 10 10 100 1k 10k 100k 1m 10m 00472-026 (db) frequency(hz) ?0.10 ?0.05 0 0.05 0.10 012345 00472-028 full-scale error (v) v ref (v) t a = 25 c v dd = 5v figure 28. full-scale error vs. v ref (buffered) figure 26. multiplying bandwidth (small-signal frequency response)
ad5303/ad5313/ad5323 rev. b | page 15 of 28 functional description the ad5303/ad5313/ad5323 are dual resistor-string dacs fabricated on a cmos process with resolutions of 8-/10-/12-bits respectively. they contain reference buffers and output buffer amplifiers, and are written to via a 3-wire serial interface. they operate from single supplies of 2.5 v to 5.5 v and the output buffer amplifiers provide rail-to-rail output swing with a slew rate of 0.7 v/s. each dac is provided with a separate reference input, which may be buffered to draw virtually no current from the reference source, or unbuffered to give a reference input range from gnd to v dd . the devices have three programmable power-down modes, in which one or both dacs may be turned off completely with a high impedance output, or the output may be pulled low by an on-chip resistor. digital-to-analog the architecture of one dac channel consists of a reference buffer and a resistor-string dac followed by an output buffer amplifier. the voltage at the v ref pin provides the reference voltage for the dac. figure 29 shows a block diagram of the dac architecture. because the input coding to the dac is straight binary, the ideal output voltage is given by n ref out d v v 2 = where: d is the decimal equivalent of the binary code, which is loaded to the dac register: 0 to 255 for ad5303 (8 bits) 0 to 1023 for ad5313 (10 bits) 0 to 4095 for ad5323 (12 bits) n is the dac resolution. input register dac register resistor string output buffer amplifier reference buffer switch controlled by control logic v ref a v out a 00472-029 figure 29. single dac channel architecture resistor string the resistor string section of the ad5303/ad5313/ad5323 is shown in figure 30 . it is simply a string of resistors, each of value r. the digital code loaded to the dac register determines at what node on the string the voltage is tapped off to be fed into the output amplifier. the voltage is tapped off by closing one of the switches connecting the string to the amplifier. because it is a string of resistors, it is guaranteed monotonic. r r r r r to output amplifier 00472-030 figure 30. resistor string dac reference inputs there is a reference input pin for each of the two dacs. the reference inputs are buffered, but can also be configured as unbuffered. the advantage with the buffered input is the high impedance it presents to the voltage source driving it. however, if the unbuffered mode is used, the user can have a reference voltage as low as gnd and as high as v dd since there is no restriction due to headroom and footroom of the reference amplifier. if there is a buffered reference in the circuit (for example, ref192 ), there is no need to use the on-chip buffers of the ad5303/ad5313/ad5323. in unbuffered mode, the input impedance is still large at typically 180 k per reference input for 0 v to v ref mode and 90 k for 0 v to 2 v ref mode. the buffered/unbuffered option is controlled by the buf a and buf b pins. if a buf pin is tied high, the reference input is buffered; if tied low, it is unbuffered. output amplifier the output buffer amplifier is capable of generating output voltages to within 1 mv of either rail, which gives an output range of 0.001 v to v dd ? 0.001 v when the reference is v dd . it is capable of driving a load of 2 k in parallel with 500 pf to gnd and v dd . the source and sink capabilities of the output amplifier can be seen in figure 17 . the slew rate is 0.7 v/s with a half-scale settling time to 0.5 lsb (at eight bits) of 6 s.
ad5303/ad5313/ad5323 rev. b | page 16 of 28 power-on reset the ad5303/ad5313/ad5323 are provided with a power-on reset function, so that they power up in a defined state. the power-on state is with 0v to v ref output range and the output set to 0 v. both input and dac registers are filled with zeros and remain so until a valid write sequence is made to the device. this is particularly useful in applications where it is important to know the state of the dac outputs while the device is powering up. clear function (clr ) the clr pin is an active low input that, when pulled low, loads all zeros to both input registers and both dac registers. this enables both analog outputs to be cleared to 0 v.
ad5303/ad5313/ad5323 rev. b | page 17 of 28 serial interface the ad5303/ad5313/ad5323 are controlled over a versatile, 3-wire serial interface, which operates at clock rates up to 30 mhz and is compatible with spi, qspi, microwire, and dsp interface standards. input shift register the input shift register is 16 bits wide. data is loaded into the device as a 16-bit word under the control of a serial clock input, sclk. the timing diagram for this operation is shown in figure 5 . the 16-bit word consists of four control bits followed by 8 /10 /12 bits of dac data, depending on the device type. the first bit loaded is the msb (bit 15), which determines whether the data is for dac a or dac b. bit 14 determines the output range (0 v to v ref or 0 v to 2 v ref ). bit 13 and bit 12 control the operating mode of the dac. table 6. control bits bit name function power-on default 15 a /b 0: data written to dac a 1: data written to dac b n/a 14 gain 0: output range of 0 v to v ref 1: output range of 0 v to 2 v ref 0 13 pd1 mode bit 0 12 pd0 mode bit 0 the remaining bits are dac data bits, starting with the msb and ending with the lsb. the ad5323 uses all 12 bits of dac data; the ad5313 uses 10 bits and ignores the 2 lsbs. the ad5303 uses eight bits and ignores the last four bits. the data format is straight binary, with all 0s corresponding to 0 v output, and all 1s corresponding to full-scale output (v ref ? 1 lsb). the sync input is a level-triggered input that acts as a frame synchronization signal and chip enable. data can be transferred into the device only while sync is low. to start the serial data transfer, sync should be taken low, observing the minimum sync to sclk rising edge setup time, t 4 . after sync goes low, serial data is shifted into the devices input shift register on the falling edges of sclk for 16 clock pulses. any data and clock pulses after the 16th are ignored, and no further serial data transfer occurs until sync is taken high and low again. sync may be taken high after the falling edge of the 16th sclk pulse, observing the minimum sclk falling edge to sync rising edge time, t 7 . after the end of serial data transfer, data is automatically transferred from the input shift register to the input register of the selected dac. if sync is taken high before the 16th falling edge of sclk, the data transfer is aborted and the input registers are not updated. when data has been transferred into both input registers, the dac registers of both dacs may be simultaneously updated, by taking ldac low. clr is an active low, asynchronous clear that clears the input and dac registers of both dacs to all 0s. low power serial interface to reduce the power consumption of the device even further, the interface only powers up fully when the device is being written to. as soon as the 16-bit control word has been written to the part, the sclk and din input buffers are powered down. they only power up again following a falling edge of sync . double-buffered interface the dacs all have double-buffered interfaces consisting of two banks of registersinput registers and dac registers. the input register is connected directly to the input shift register and the digital code is transferred to the relevant input register on com- pletion of a valid write sequence. the dac register contains the digital code used by the resistor string. access to the dac register is controlled by the ldac function. when ldac is high, the dac register is latched and the input register may change state without affecting the contents of the dac register. however, when ldac is brought low, the dac register becomes transparent and the contents of the input reg- ister are transferred to it. this is useful if the user requires simultaneous updating of both dac outputs. the user may write to both input registers individually and then, by pulsing the ldac input low, both outputs update simultaneously. these parts contain an extra feature whereby the dac register is not updated unless its input register has been updated since the last time that ldac was brought low. normally, when ldac is brought low, the dac registers are filled with the contents of the input registers. in the case of the ad5303/ad5313/ad5323, the part only updates the dac register if the input register has been changed since the last time the dac register was updated, thereby removing unnecessary digital crosstalk.
ad5303/ad5313/ad5323 rev. b | page 18 of 28 db15 (msb) db0 (lsb) pd0 d7 d6 d5 d4 d3 d2 d1 d0 pd1 gain x x x x data bits 00472-031 a/b figure 31. ad5303 input shift register contents db15 (msb) db0 (lsb) pd0 d7d6d5d4d3d2d1d0 pd1 gain xx data bits 0 0472-032 a/b d9 d8 figure 32. ad5313 input shift register contents db15 (msb) db0 (lsb) pd0 d7d6d5d4d3d2d1d0 pd1 gain data bits 00472-033 a/b d9 d8 d11 d10 figure 33. ad5323 input shift register contents
ad5303/ad5313/ad5323 rev. b | page 19 of 28 power-down modes the ad5303/ad5313/ad5323 have very low power consump- tion, dissipating only 0.7 mw with a 3 v supply and 1.5 mw with a 5 v supply. power consumption can be further reduced when the dacs are not in use by putting them into one of three power-down modes, which are selected by bit 13 and bit 12 (pd1 and pd0) of the control word. table 7 shows how the state of the bits corresponds to the mode of operation of that particular dac. table 7. pd1/pd0 operating modes pd1 pd0 operating mode 0 0 normal operation 0 1 power-down (1 k load to gnd) 1 0 power-down (100 k load to gnd) 1 1 power-down (high impedance output) when both bits are set to 0, the dacs work normally with their normal power consumption of 300 a at 5 v. however, for the three power-down modes, the supply current falls to 200 na at 5 v (50 na at 3 v) when both dacs are powered down. not only does the supply current drop, but the output stage is also internally switched from the output of the amplifier to a resistor network of known values. this has the advantage that the output impedance of the part is known while the part is in power-down mode and provides a defined input condition for whatever is connected to the output of the dac amplifier. there are three different power-down options. the output is connected internally to gnd through either a 1 k resistor or a 100 k resistor, or it is left in a high impedance state (three- state). the output stage is illustrated in figure 34 . the bias generator, the output amplifier, the resistor string, and all other associated linear circuitry are shut down when the power-down mode is activated. however, the contents of the registers are unaffected when in power-down. the time to exit power-down is typically 2.5 s for v dd = 5 v and 5 s when v dd = 3 v (see figure 24 for a plot). the software power-down modes programmed by pd0 and pd1 are overridden by the pd pin. taking this pin low puts both dacs into power-down mode simultaneously and both outputs are put into a high impedance state. if pd is not used, it should be tied high. resistor string dac a mplifie r v out 00472-034 power-down circuitry resistor network figure 34. output stage during power-down
ad5303/ad5313/ad5323 rev. b | page 20 of 28 microprocesser interfacing ad5303/ad5313/ad5323 to adsp-2101 interface figure 35 shows a serial interface between the ad5303/ad5313/ ad5323 and the adsp-2101 . the adsp-2101 should be set up to operate in the sport transmit alternate framing mode. the adsp-2101 sport is programmed through the sport control register and should be configured as follows: internal clock operation, active-low framing, 16-bit word length. transmission is initiated by writing a word to the tx register after the sport has been enabled. sclk din sync tfs dt sclk * additional pins omitted for clarity 00472-035 ad5303/ ad5313/ ad5323* adsp-2101 figure 35. ad5303/ad5313/ad5323 to adsp-2101 interface ad5303/ad5313/ad5323 to 68hc11/68l11 interface figure 36 shows a serial interface between the ad5303/ ad5313/ad5323 and the 68hc11/68l11 microcontroller. sck of the 68hc11/68l11 drives the sclk of the ad5303/ ad5313/ad5323, while the mosi output drives the serial data line (din) of the dac. the sync signal is derived from a port line (pc7). the setup conditions for correct operation of this interface are as follows: the 68hc11/68l11 should be con- figured so that its cpol bit is a 0 and its cpha bit is a 1. when data is being transmitted to the dac, the sync line is taken low (pc7). when the 68hc11/68l11 is configured as previously mentioned, data appearing on the mosi output is valid on the falling edge of sck. serial data from the 68hc11/ 68l11 is transmitted in 8-bit bytes with only eight falling clock edges occurring in the transmit cycle. data is transmitted msb first. to load data to the ad5303/ad5313/ ad5323, pc7 is left low after the first eight bits are transferred and a second serial write operation is performed to the dac; pc7 is taken high at the end of this procedure. din sclk sync pc7 sck mosi 68hc11/68l11* *additional pins omitted for clarity 0 0 4 7 2 - 0 3 6 ad5303/ ad5313/ ad5323* figure 36. ad5303/ad5313/ad5323 to 68hc11/68l11 interface ad5303/ad5313/ad5323 to 80c51/80l51 interface figure 37 shows a serial interface between the ad5303/ ad5313/ad5323 and the 80c51/80l51 microcontroller. the setup for the interface is as follows: txd of the 80c51/80l51 drives sclk of the ad5303/ad5313/ad5323, while rxd drives the serial data line of the part. the sync signal is again derived from a bit programmable pin on the port. in this case, port line p3.3 is used. when data is to be transmitted to the ad5303/ad5313/ad5323, p3.3 is taken low. the 80c51/80l51 transmits data only in 8-bit bytes; thus only eight falling clock edges occur in the transmit cycle. to load data to the dac, p3.3 is left low after the first eight bits are transmitted and a second write cycle is initiated to transmit the second byte of data. p3.3 is taken high following the completion of this cycle. the 80c51/ 80l51 output the serial data in a format that has the lsb first. the ad5303/ad5313/ad5323 require data with msb as the first bit received. the 80c51/80l51 transmit routine should take this into account. din sclk p3.3 txd rxd 80c51/80l51* *additional pins omitted for clarity. 00472-037 sync ad5303/ ad5313/ ad5323* figure 37. ad5303/ad5313/ad5323 to 80c51/80l51 interface ad5303/ad5313/ad5323 to microwire interface figure 38 shows an interface between the ad5303/ad5313/ ad5323 and any microwire-compatible device. serial data is shifted out on the falling edge of the serial clock and is clocked into the ad5303/ad5313/ad5323 on the rising edge of the sk. din sclk sk so microwire* * additional pins omitted for clarity. 00472-038 cs sync ad5303/ ad5313/ ad5323* figure 38. ad5303/ad5313/ad5323 to microwire interface
ad5303/ad5313/ad5323 rev. b | page 21 of 28 applications information typical application circuit the ad5303/ad5313/ad5323 can be used with a wide range of reference voltages, especially if the reference inputs are con- figured to be unbuffered, in which case the devices offer a full, one-quadrant multiplying capability over a reference range of 0 v to v dd . more typically, the ad5303/ad5313/ad5323 may be used with a fixed precision reference voltage. figure 39 shows a typical setup for the ad5303/ad5313/ad5323 when using an external reference. if the reference inputs are unbuffered, the reference input range is from 0 v to v dd , but if the on-chip reference buffers are used, the reference range is reduced. suit- able references for 5 v operation are the ad780 and ref192 (2.5 v references). for 2.5 v operation, a suitable external reference is the ref191 , a 2.048 v reference. sclk din gnd ad5303/ad5313/ ad5323 serial interface ext ref 00472-039 ad780/ref192 with v dd = 5v or ref191 with v dd = 2.5v v out sync v out a v out b v ref a v ref b 1f v dd = 2.5v to 5.5 v v dd buf a buf b figure 39. ad5303/ad5313/ad5323 using external reference if an output range of 0 v to v dd is required when the reference inputs are configured as unbuffered (for example, 0 v to 5 v), the simplest solution is to connect the reference inputs to v dd . as this supply may not be very accurate and may be noisy, the ad5303/ad5313/ad5323 can be powered from the reference voltage, for example, using a 5 v reference such as the ref195 , as shown in figure 40 . the ref195 outputs a steady supply voltage for the ad5303/ad5313/ad5323. the supply current required from the ref195 is 300 a and approximately 30 a or 60 a into each of the reference inputs (if unbuffered). this is with no load on the dac outputs. when the dac outputs are loaded, the ref195 also needs to supply the current to the loads. the total current required (with a 10 k load on each output) is 360 a + 2(5 v/10 k) = 1.36 ma the load regulation of the ref195 is typically 2 ppm/ma, which results in an error of 2.7 ppm (13.5 v) for the 1.36 ma current drawn from it. this corresponds to a 0.0007 lsb error at eight bits and 0.011 lsb error at 12 bits. sclk din ad5303/ad5313/ ad5323 serial interface ref195 00472-040 output sync v out a v out b v dd v ref a 1f 15 v gnd v s v ref b 0.1f 10f gnd buf a buf b figure 40. using an ref195 as power and reference to the ad5303/ad5313/ad5323 bipolar operation using the ad5303/ ad5313/ad5323 the ad5303/ad5313/ad5323 have been designed for single- supply operation, but bipolar operation is also achievable using the circuit shown in figure 41 . the circuit shown has been con- figured to achieve an output voltage range of ?5 v < v out < +5 v. rail-to-rail operation at the amplifier output is achievable using an ad820 or op295 as the output amplifier. sclk din ad5303/ad5313/ ad5323 serial interface ref195 00472-041 sync v out a/b v ref a/b 1f gnd 6v to 16 v 0.1f 10f v dd v dd = 5v +5v ?5v r2 10k ? ad820/ op295 r1 10k? 5v gnd buf a buf b output v s figure 41. bipolar operation using the ad5303/ad5313/ad5323 the output voltage for any input code can be calculated as follows: )/( /)()2/()( r1r2vr1r2r1 dvv ref n ref out where: d is the decimal equivalent of the code loaded to the dac. n is the dac resolution. v ref is the reference voltage input, and gain bit = 0, with v ref = 5 v r1 = r2 = 10 k and v dd = 5 v, v d v n out 5)2/10( u
ad5303/ad5313/ad5323 rev. b | page 22 of 28 opto-isolated interface for process control applications the ad5303/ad5313/ad5323 has a versatile 3-wire serial interface making it ideal for generating accurate voltages in process control and industrial applications. due to noise, safety requirements, or distance, it may be necessary to isolate the ad5303/ad5313/ad5323 from the controller. this can easily be achieved by using opto-isolators, which provides isolation in excess of 3 kv. the serial loading structure of the ad5303/ ad5313/ad5323 makes it ideally suited for use in opto-isolated applications. figure 42 shows an opto-isolated interface to the ad5303/ad5313/ad5323 where din, sclk, and sync are driven from opto-couplers. the power supply to the part also needs to be isolated. this is done by using a transformer. on the dac side of the transformer, a 5 v regulator provides the 5 v supply required for the ad5303/ad5313/ad5323. sclk din ad5303/ad5313/ ad5323 00472-042 sync 5v regulator power v dd 10f 0.1f v out a v out b v ref b v ref a v dd 10k ? 10k ? 10k ? din s yn c scl k v dd v dd gnd buf a buf b figure 42. ad5303/ad5313/ad5323 in an opto-isolated interface decoding multiple ad5303/ad5313/ad5323s the sync pin on the ad5303/ad5313/ad5323 can be used in applications to decode a number of dacs. in this application, all the dacs in the system receive the same serial clock and serial data, but only the sync to one of the devices is active at any one time, allowing access to two channels in this 8-channel system. the 74hc139 is used as a 2-to-4 line decoder to address any of the dacs in the system. to prevent timing errors from occurring, the enable input should be brought to its inactive state while the coded address inputs are changing state. figure 43 shows a diagram of a typical setup for decoding multiple ad5303/ad5313/ad5323 devices in a system. 00472-043 sclk din din sclk ad5303/ ad5313/ ad5323 sync 74hc139 enable coded address 1g 1a 1b dgnd 1y0 1y1 1y2 1y3 v cc v dd din sclk ad5303/ ad5313/ ad5323 sync din sclk ad5303/ ad5313/ ad5323 sync din sclk ad5303/ ad5313/ ad5323 sync figure 43. decoding multiple ad5303/ad5313/ad5323 devices in a system ad5303/ad5313/ad5323 as a digitally programmable window detector a digitally programmable upper/lower limit detector using the two dacs in the ad5303/ad5313/ad5323 is shown in figure 44 . the upper and lower limits for the test are loaded to dac a and dac b, which, in turn, set the limits on the cmp04 . if the signal at the v in input is not within the pro- grammed window, an led indicates the fail condition. 5 v 1/2 cmp04 fail pass 1/6 74hc05 v ref sclk din v out a v dd 00472-044 ad5303/ad5313/ ad5323 v ref a gnd 0.1f 10f 1k ? 1k ? v in pass/fail din sclk sync sync v ref b v out b figure 44. window detector using ad5303/ad5313/ad5323
ad5303/ad5313/ad5323 rev. b | page 23 of 28 coarse and fine adjustment using the ad5303/ad5313/ad5323 the dacs in the ad5303/ad5313/ad5323 can be paired together to form a coarse and fine adjustment function, as shown in figure 45 . dac a provides the coarse adjustment while dac b provides the fine adjustment. varying the ratio of r1 and r2 changes the relative effect of the coarse and fine adjustments. with the resistor values and external reference shown, the output amplifier has unity gain for the dac a output, so the output range is 0 v to 2.5 v ? 1 lsb. for dac b, the amplifier has a gain of 7.6 10 C3 , giving dac b a range equal to 19 mv. the circuit is shown with a 2.5 v reference, but reference voltages up to v dd may be used. the op amps indicated allow a rail-to-rail output swing. gnd ad5303/ad5313/ ad5323 ext 2.5v ref 00472-045 v out v out b v ref a 1f gnd v in 0.1f 10f v dd v dd = 5 v +5v ad820/ op295 v out a v ref b r2 51.2k ? r1 390 ? v out r4 900 ? r3 51.2k ? ad780/ref192 w ith v dd = 5v figure 45. coarse and fine adjustment daisy-chain mode this mode is used for updating serially connected or standalone devices on the rising edge of sync . for systems that contain several dacs, or where the user wishes to read back the dac contents for diagnostic purposes, the sdo pin may be used to daisy-chain several devices together and provide serial readback. by connecting the daisy-chain enable (dcen) pin high, the daisy-chain mode is enabled. it is tied low in standalone mode. in daisy-chain mode, the internal gating on sclk is disabled. the sclk is continuously applied to the input shift register when sync is low. if more than 16 clock pulses are applied, the data ripples out of the shift register and appears on the sdo line. this data is clocked out after the falling edge of sclk and is valid on the subsequent rising and falling edges. by connect- ing this line to the din input on the next dac in the chain, a multidac interface is constructed. sixteen clock pulses are required for each dac in the system. therefore, the total number of clock cycles must equal 16n, where n is the total number of devices in the chain. when the serial transfer to all devices is complete, sync should be taken high. this prevents any further data from being clocked into the input shift register. a continuous sclk source may be used if it can be arranged that sync is held low for the correct number of clock cycles. alternatively, a burst clock containing the exact number of clock cycles may be used and sync may be taken high some time later. when the transfer to all input registers is complete, a common ldac signal updates all dac registers and all analog outputs are updated simultaneously. 00472-046 68hc11 1 miso mosi sck pc7 pc6 din sclk ad5303/ ad5313/ ad5323 1 (dac 1) sync ldac sdo sclk ad5303/ ad5313/ ad5323 1 (dac 2) sync ldac sdo din sclk ad5303/ ad5313/ ad5323 1 (dac n) sync ldac sdo din 1 additional pins omitted for clarity. figure 46. daisy-chain mode
ad5303/ad5313/ad5323 rev. b | page 24 of 28 00472-047 sclk din db15 db0 db15 db0 db15 db0 sdo input word for dac n input word for dac (n+1) undefined input word for dac n sclk sdo t 1 t 2 t 3 t 4 t 6 t 5 t 8 t 14 t 15 t 13 t 12 v il v ih sync figure 47. daisy-chai ning timing diagram power supply bypassing and grounding in any circuit where accuracy is important, careful considera- tion of the power supply and ground return layout helps to ensure the rated performance. the printed circuit board on which the ad5303/ad5313/ad5323 are mounted should be designed so that the analog and digital sections are separated and confined to certain areas of the board. if the ad5303/ ad5313/ad5323 are in a system where multiple devices require an agnd-to-dgnd connection, the connection should be made at one point only. the star ground point should be established as close as possible to the ad5303/ ad5313/ad5323. the ad5303/ad5313/ad5323 should have ample supply bypassing of 10 f in parallel with 0.1 f on the supply located as close to the package as possible, ideally right up against the device. use 10 f capacitors that are of the tantalum bead type. the 0.1 f capacitor should have low effective series resistance (esr) and effective series inductance (esi), like the common ceramic types that provide a low impedance path to ground at high frequencies to handle transient currents due to internal logic switching. the power supply lines of the ad5303/ad5313/ad5323 should use as large a trace as possible to provide low impedance paths and reduce the effects of glitches on the power supply line. fast switching signals such as clocks should be shielded with digital ground to avoid radiating noise to other parts of the board, and should never be run near the reference inputs. avoid crossover of digital and analog signals. traces on opposite sides of the board should run at right angles to each other. this reduces the effects of feedthrough through the board. a microstrip technique is by far the best, but is not always possible with a double-sided board. in this technique, the component side of the board is dedicated to the ground plane while signal traces are placed on the solder side.
ad5303/ad5313/ad5323 rev. b | page 25 of 28 outline dimensions 16 9 8 1 pin 1 seating plane 8 0 4.50 4.40 4.30 6.40 bsc 5.10 5.00 4.90 0.65 bsc 0.15 0.05 1.20 max 0.20 0.09 0.75 0.60 0.45 0.30 0.19 coplanarity 0.10 compliant to jedec standards mo-153-ab figure 48. 16-lead thin shrink small outline package [tssop] (ru-16) dimensions shown in millimeters ordering guide model temperature range package description package option ad5303aru C40c to +105c 16-lead thin shrink small outline package (tssop) ru-16 ad5303aru-reel7 C40c to +105c 16-lead thin shrink small outline package (tssop) ru-16 ad5303aruz 1 C40c to +105c 16-lead thin shrink small outline package (tssop) ru-16 ad5303bru C40c to +105c 16-lead thin shrink small outline package (tssop) ru-16 ad5303bru-reel C40c to +105c 16-lead thin shrink small outline package (tssop) ru-16 ad5303bru-reel7 C40c to +105c 16-lead thin shrink small outline package (tssop) ru-16 ad5303bruz 1 C40c to +105c 16-lead thin shrink small outline package (tssop) ru-16 ad5303bruz-reel7 1 C40c to +105c 16-lead thin shrink small outline package (tssop) ru-16 ad5313aru C40c to +105c 16-lead thin shrink small outline package (tssop) ru-16 ad5313aru-reel7 C40c to +105c 16-lead thin shrink small outline package (tssop) ru-16 ad5313aruz 1 C40c to +105c 16-lead thin shrink small outline package (tssop) ru-16 ad5313bru C40c to +105c 16-lead thin shrink small outline package (tssop) ru-16 ad5313bru-reel C40c to +105c 16-lead thin shrink small outline package (tssop) ru-16 ad5313bru-reel7 C40c to +105c 16-lead thin shrink small outline package (tssop) ru-16 ad5313bruz 1 C40c to +105c 16-lead thin shrink small outline package (tssop) ru-16 ad5323aru C40c to +105c 16-lead thin shrink small outline package (tssop) ru-16 ad5323aru-reel7 C40c to +105c 16-lead thin shrink small outline package (tssop) ru-16 ad5323aruz 1 C40c to +105c 16-lead thin shrink small outline package (tssop) ru-16 ad5323aruz-reel7 1 C40c to +105c 16-lead thin shrink small outline package (tssop) ru-16 ad5323bru C40c to +105c 16-lead thin shrink small outline package (tssop) ru-16 ad5323bru-reel C40c to +105c 16-lead thin shrink small outline package (tssop) ru-16 ad5323bru-reel7 C40c to +105c 16-lead thin shrink small outline package (tssop) ru-16 ad5323bruz 1 C40c to +105c 16-lead thin shrink small outline package (tssop) ru-16 AD5323BRUZ-REEL 1 C40c to +105c 16-lead thin shrink small outline package (tssop) ru-16 AD5323BRUZ-REEL7 1 C40c to +105c 16-lead thin shrink small outline package (tssop) ru-16 1 z = rohs compliant part.
ad5303/ad5313/ad5323 rev. b | page 26 of 28 notes
ad5303/ad5313/ad5323 rev. b | page 27 of 28 notes
ad5303/ad5313/ad5323 rev. b | page 28 of 28 notes ?1999C2007 analog devices, inc. all rights reserved. trademarks and registered trademarks are the property of their respective owners. c00472-0-6/07(b)

▲Up To Search▲

Price & Availability of AD5323BRUZ-REEL

	To Download AD5323BRUZ-REEL Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .